2 Port Serial ATA Cardbus

The SATA PCMCIA are compliant with Serial ATA 1.0 specifications to upgrade your laptop computer for use with Dual Serial ATA RAID Channels. Support up to two devices.

The PC Card provides two fully compliant Serial ATA ports Striping (RAID 0) and Mirroring (RAID 1) are supported to improve data performance and provide data redundancy.

•  
• SPECIFICATION :
• • Serial ATA - 1.5 Gbps (150 MB/s)
• • Compliant with Serial ATA 1.0 Specification
• • Supports 48-bit LBA (Large Disk), hard drives larger than 137 GB
• • Supports spread spectrum clocking to reduce EMI
• • Compliant with 32 bit Type 2 Cardbus
•  
• INTERFACE :
• • Supports SATA 1.0 (High Speed Serialised AT Attachment, Revision 1.0), 1.5 Gb/s data rate
• • Supports Host adaptor register Interface (SCR, Status and Control Registers)
• • Supports 48-bit LBA (Large Disk), hard drives larger than 137 GB

Serial ATA IDE Adaptor

The SATA IDE Adaptor attaches to the back of all ATAPI, ATA 133, 100, 66, 33, EIDE and IDE Storage devices (Such as a Hard Drive, DVD, DVD Writer, CD-ROM, CD Writer etc) and allows the device to become compliant with Serial ATA Host devices.

•  
• SPECIFICATION :
• • Serial ATA - 1.5 Gbps (150 MB/s)
• • Compliant with Serial ATA 1.0 Specification
• • Supports 48-bit LBA (Large Disk), hard drives larger than 137 GB
• • Supports spread spectrum clocking to reduce EMI
• • Compatible with all EIDE and IDE Devices

Bi-Directional SATA - IDE Adaptor, Compatible with Hard Disk Drives

The SATA DUAL ADAPTOR is a bi-directional converter for serial and parallel ATA translation. The Serial ATA physical, link, and transport layers are compliant to Serial ATA 1.0. The SATA DUAL ADAPTOR converter supports a 1.5GHz data rate. The application layer supports both the ATA register command set and PACKET command set, which could drive both Hard Disk Drive and ATAPI Optical Storage such as CR-ROM, CD-RW, DVD-ROM, DVD-RW, etc. The Serial ATA and the Parallel ATA application layer support both host and device operation.

Easy to install and setup, simply connect devices and slide switch to correct position. If converting SATA to IDE choose device and when converting IDE to SATA select host.

•  
• SPECIFICATION :
• • Serial ATA 1.0 specification 1.5Gbps
• • ATA/ATAPI PIO mode 0 – 4
• • ATA/ATAPI Ultra DMA 16.7, 25, 33, 48, 66, 100,
  133 & 150Mb/s
• • Supports Serial ATA hot-plug
• • Low power consumption
• • Supports AC and DC

Serial ATA PCI Host Cards

• 2x SATA & 1x IDE PCI Card

• 1x INT / 1x EXT SATA & 1x IDE PCI Raid Card

• 1x INT SATA 1x EXT ESATA & 1x IDE PCI Raid Card

Serial ATA (or SATA) has been designed as a replacement for the existing 40 way IDE cable, the SATA connector and cable are smaller (which improves air circulation), with a reduced operating voltage and pin amount (7 as opposed to 40), the current data transfer rate is ATA- 150 (1.5Gbps). Each connected SATA device or conversion needs it’s own cable, this removes the old master/ slave set-up and allows for improved data transmission and access speed.

The SATA PCI Cards are compliant with Serial ATA 1.0 specifications to upgrade your desktop computer to allow Dual Serial ATA RAID Channels and one Parallel ATA (IDE) Host controller to support up to two devices

The PCI Cards provide two fully compliant Serial ATA ports to access Striping (RAID 0) and Mirroring (RAID 1) are supported to improve data performance and provide data redundancy

•  
• SPECIFICATION :
• • Serial ATA - 1.5 Gbps (150 MB/s)
• • Compliant with Serial ATA 1.0 Specification
• • Supports 48-bit LBA (Large Disk), hard drives larger than 137 GB
• • Supports spread spectrum clocking to reduce EMI
• • Registers as compatible with Parallel ATA
• • Single, digital PLL architecture with 1 PLL for both channels